Touchless Car Wash at Home Complete Guide


Touchless car wash

Touchless Car Wash  Method of washing cars is simply the same thing – a way to wash a car with no touching it physically.

The goal of this technique is to eliminate completely the possibility of creating scratch marks and swirls on the coat that covers your vehicle or truck during the cleaning process.

This may sound excessive to some people, however if you’ve ever walked by an automobile with swirls and scratches you’ll see the rationale behind taking the time and effort.

These scratches aren’t particularly large and, in dim light they’re not obvious. In bright light however particularly on dark-colored automobiles, they can make cars look awful.

There are touchless auto washes that perform the same task, however they differ in the kind of soap that is used. Automated Touchless Car Wash make use of an extra aggressive soap that is slightly harsh, but is more effective at dissolving the bonds dirt forms formed with the paint. We’ll use a gentler soap for Touchless Jeep Wrangler Wash.

Let’s begin by examining the process.

The Touchless Method Step-By-Step

1 – Find a Shaded Spot to Wash Your Car

The direct sunlight can cause your vehicle to dry too fast. The result will be water spots, unless you have water that is particularly soft that is used to wash.

Minerals found in hard water will produce lighter-colored deposits on the surfaces of the paint.

Additionally, you shouldn’t allow the soap to get dried on the outside of your vehicle. This could create spots, and also prevent the road grime that was previously loose from washing away after being washed.

2 – Rinse Your Car or Truck Well

Get rid of the dirt and other debris using this power-washer as much as you can. Make sure to blast every surface thoroughly and try to take care of those areas that are particularly dirty.

Be careful around window seals as well as side mirrors and any other surface that may not be able to handle the pressure of the pressure washer.

3 – Use a Foam Cannon to cover your vehicle with Suds

Utilize a foam cannon thoroughly soak your car in suds from car shampoo. The thicker , the more effective.

If you’re not sure the concept of a foam cannon it’s a simple accessory you can attach to your power washer. It enables you to add soap into the stream of spray and produce an extremely thick and fluffy coating of suds.

4 – Let the Soap Sit and Break Down the Dirt

Allow the soap to sit for a while and remove dirt and grime stuck on the finish of the finishing.

The soap should be left on the car for at the least 5 minutes or longer. This will allow it the time it needs to complete its task.

5 – Rinse the Soap Off With a Pressure Washer

The power washer is likely to help get rid of the remaining grime and grit which the shampoo for cars loosens.

You might need repeat the steps 3 and 4, in case you aren’t satisfied with the outcome.

The touchless approach isn’t the best for vehicles or trucks that have tar, bugs guts, and other contaminants that have adhered to the road surface.

If that’s the case, you might need to change to the 2-bucket option.

6 -Dry the Car using an Air Dryer

An air dryer is an air blower that is forced, similar to a leaf-blower. A leaf blower is a viable option however it’s not as efficient.

The best detailing air dryers come with a soft tip of rubber to avoid damaging the finish when you bump it. Leaf blowers generally come with a plastic outlet , which means you’ll have to be extra cautious. Additionally, they tend to be less focused and might not be as effective in removing water from difficult spaces.

Be sure to go through crevices and cracks like rear view mirrors, as well as seams of the body panel.

This will stop the water from draining in the future when you move your vehicle and leaving water spots after the water is dry.

What is required to carry out the Touchless Method

Electric Pressure Washer

Gas pressure washers are expensive, powerful and difficult to control. A pressure washer that is electric is a better option. They’re significantly less expensive than gas-powered models, smaller and lighter and offer the correct quantity of pressure.

Unfortunately , many electronic power washers were manufactured at a low cost and don’t last. Be sure to do your research and locate a quality electrical pressure washer.

My suggestion is to purchase Sun Joe SPX9007-PRO. Sun Joe SPX9007-PRO. This pressure washer comes with an electric motor. It’s slightly more expensive than the top models you’ll find on the internet, but it’s not likely to be able to last after just a couple of usages. It’s part of the Sun Joe Commercial line and is made of brass and other metals , instead of plastic that doesn’t stand up to the high pressures repeatedly employed very well.

If you need to opt for a more affordable alternative, I suggest that you purchase the K1700 from Karcher. It’s more durable that the majority of the models made of plastic, and it comes with an excellent warranty which will replace the unit if there is a problem.

If you’ve got the money serious detailers opt to the Kranzle K-1122 TST. It has a higher flow rate and has the ability to push more pressure than the Karcher as well as Sun Joe without exceeding a safe amount. Unfortunately, I don’t have the resources or a loving wife who would not divorce me if I set out to achieve this goal. YMMV.

Ph Neutral Car Shampoo

It is tempting to make use of dish soap in the kitchen but it is an error. Dishwashing soap is too harsh and will remove sealant and wax off your finish. A quality car shampoo is pH neutral which is constructed to avoid being rough on dirt but not wax or other protective coatings.

There are many great car shampoos available. Chemical Guys has a variety of great products like Mr. Pink. If you already have a preferred from a trusted manufacturer, there’s no reason to change.

Foam Cannon

The foam gun is an accessory you’ll need to soak your vehicle or car in suds. The cannon will be attached at the top of your washer. You’ll then blast soapy suds across and let the shampoo for your car to sit for a while and remove grime and dirt.

If you’re planning to use the Sun Joe SPX9007PRO, I suggest using it with the Sun Joe Foam Cannon. The reason for this is that there are a variety of reports about third-party foam cannons not working when used with the SPX9007PRO. There is a drop in pressure on certain third party cannons, which causes the process of obtaining a thick layer of foam harder.

Air Dryer

While you can do it using a leaf blower a high-quality automotive air dryer is more effective in taking water out of cracks and crevices in which water could be hidden.

If the water that’s in between body panels isn’t cleared, it will drain across the back of your vehicle the moment you drive off. It will , of course, cause water spots to form.

 

 


Like it? Share with your friends!

What's Your Reaction?

hate hate
0
hate
confused confused
0
confused
fail fail
0
fail
fun fun
0
fun
geeky geeky
0
geeky
love love
0
love
lol lol
0
lol
omg omg
0
omg
win win
0
win
Alex James

0 Comments

Your email address will not be published.